AI Music Video Generator

Decibel meter.

A sound level meter that runs on your microphone. It measures dBFS exactly, and it will not pretend that number is dB SPL until you give it a reference to calibrate against. Nothing is recorded and nothing is uploaded.

Read this before you trust a number. A browser is given sample values, not air pressure. It has no way to know how sensitive your microphone is or how much gain sits behind it, so it cannot produce a true dB SPL figure on its own. What is below is dBFS — how far the signal sits under the loudest value the format can hold — and it is exact. Set a calibration offset and it becomes SPL on this device.

—

dBFS — relative, not SPL

Peak
—
Quietest, 10s
—
Loudest, 10s
—

Calibration

If you have a reading you trust — a real sound level meter, a calibrator, a measured room — play a steady sound, type what the reference says, and this works out the one offset that turns this microphone's dBFS into dB SPL. Without that reading, the offset is a guess and the page will keep calling the number dBFS.

Measured. Now what does the song look like?

Do you want more monthly listeners?

Tap to choose your song

MP3, WAV, M4A or AAC, up to 150 MB

No account, no card. Decide once you've seen it.

What to know first

No browser can measure dB SPL on its own. A microphone turns pressure into a voltage, and how much voltage it makes for a given pressure is its sensitivity — a number printed on a measurement mic and unpublished for the one in your phone. A preamp then multiplies it by an amount the operating system chooses. The browser is handed the result and none of the steps. So the honest output is dBFS: how far the signal sits below the loudest value the format can hold. That part is arithmetic, and it is exact.

Every other browser decibel meter has the same problem. If one shows you 62 dB with no calibration step, it has added a fixed number to the dBFS it measured and hoped your device resembles whatever it was tuned on. On some hardware that lands close. On other hardware it is 20 dB out, in either direction, and nothing on screen tells you which you got.

The offset fixes it, if you have a reference. The gap between dBFS and SPL is one constant for a given microphone at a given gain. Measure a steady sound with something you trust, type its reading in, and every figure afterwards is real SPL on this device — until the operating system changes the input volume, at which point it is wrong again and needs redoing.

Automatic gain control is turned off here. The microphone is opened with echo cancellation, noise suppression and auto gain all disabled, because each one changes the level on its own. Auto gain is the worst of them: it turns the input down when a room gets loud, which is the exact moment a meter should read higher.

Phone microphones give up before loud things do. They are built for speech and most of them distort somewhere around 100 to 120 dB SPL. Past that the reading stops climbing whatever you do, so a phone cannot tell you whether a concert is at 105 or 125 — and that is the range where the answer matters.

Nothing is recorded. The microphone feeds the level calculation directly in your browser. No audio is stored and none is sent anywhere.

Questions

Why does it show dBFS instead of decibels?
Because dBFS is what a browser can actually measure. dB SPL describes pressure in air, and working it out needs the sensitivity of your microphone and the gain applied to it, neither of which a web page can read. dBFS is measured from the samples themselves and is exact.
How do I make it read in dB SPL?
Calibrate it once. Play a steady sound, read it on a meter you trust, and type that figure into the reference box while this page is measuring. It works out the single offset between the two and applies it to every later reading.
How accurate is it after calibration?
As accurate as your reference was, as long as nothing changes. The offset holds for that microphone at that input gain. Change the input volume in your system settings, plug in a different mic, or move to a very different frequency range, and it needs doing again.
Can I use it to check if a workplace is too loud?
Not for anything official. Workplace noise limits are enforced against meters built to IEC 61672 and calibrated on a schedule, and a phone microphone meets none of that. This is useful for comparing one moment to another, and for a calibrated rough figure.
Why does the number move when nothing changed?
Because the room is not silent and the meter is fast. It rises quickly to catch a peak and falls slowly so the figure can be read, which is how a physical meter on its fast setting behaves.
What is a normal reading?
In dBFS, a quiet room on a laptop mic usually sits somewhere between -60 and -45, conversation around -30, and a shout close to the mic near 0. Those are relative to the device, which is the point: they are not decibels of sound in the air.
Is my microphone recorded?
No. The audio goes straight into the level calculation in your browser and is never stored or sent anywhere.

Other free tools

Still here? Then you care how it looks.

Do you want more monthly listeners?

Tap to choose your song

MP3, WAV, M4A or AAC, up to 150 MB

No account, no card. Decide once you've seen it.

Do you want more monthly listeners?

Try it free